原裝SMC回轉驅動型2爪型氣爪
如果您對該產品感興趣的話,可以
產品名稱: 原裝SMC回轉驅動型2爪型氣爪
產品型號: MDBB63-50Z
產品展商: SMC
產品文檔: 無相關文檔
簡單介紹
原裝SMC回轉驅動型2爪型氣爪
內燃機缸體上安放活塞的空腔。是活塞運動的軌道，燃?xì)庠谄渲腥紵芭蛎?，通過氣缸壁還能散去一部分燃?xì)鈧鹘o的爆發余熱，使發動機保持正常的工作溫度。氣缸的型式有整體式和單鑄式。單鑄式又分為干式和濕式兩種。
原裝SMC回轉驅動型2爪型氣爪
的詳細介紹
原裝SMC回轉驅動型2爪型氣爪
內置磁環 D 內置磁環
安裝方式 B 基本型
缸徑 63 缸徑 63mm
通口螺紋的種類 - Rc
氣缸行程 50 氣缸行程 50mm
氣缸追記號 - 無防護套,氣緩沖
行程調整標記 - 無
雙行程標記 - 行程標記
氣缸行程2 - 無氣缸行程2
氣缸追記號2 - 無防護套,氣緩沖
附件1 - 無
附件2 - 無
磁性開關型號 - 無磁性開關
磁性開關個數 - 2個 或 無
? Indication of effective gripping force
The effective gripping force shown in the
graphs to the right is expressed as F, which is
Gripping Force” for details of Gripping force at each
gripping point. Value of effective
gripping force is measured at the middle of
opening/closing stroke.
Note 2) ( ) Value shows MDHR mass,
but it does not include auto switch mass.
the thrust of one finger, when both fingers and
attachments are in full contact with the
workpiece as shown in the figure below.
When the finger opening/closing speed is
set as the total stroke of 0.2 seconds
or more, it may cause the
product to stick or completely stop its movement.
? Workpiece gripping point should be within the
gripping point range: The range shown for
each operating pressure given in the graphs tothe right.
? When the gripping point distance becomes
large, the finger attachment applies an
excessively large load to the finger sliding
section, causing excessive play of the fingers
and possibly leading to premature failure.
Note 1) Refer to page 494 “Effective
原裝SMC回轉驅動型2爪型氣爪
